SSPC AB 1 EBOOK

You are purchasing a downloadable pdf of this Standard. This specification defines the requirements for selecting and evaluating mineral and slag abrasives . 6 Feb JETMAGĀ® abrasive was analyzed in accordance with the required qualification tests of. SSPC-AB 1 for specific gravity, hardness, weight. 15 Feb Mineral and Slag Abrasives (Abrasive Specification No. 1).

Author: Kigarr Mibei
Country: Pacific Islands
Language: English (Spanish)
Genre: Software
Published (Last): 19 January 2006
Pages: 251
PDF File Size: 17.81 Mb
ePub File Size: 6.13 Mb
ISBN: 803-9-64077-917-3
Downloads: 32460
Price: Free* [*Free Regsitration Required]
Uploader: Mezirr

The Importance of Monitoring Abrasive CleanlinessKTA University

The cleanliness of the abrasive whether new or recycled is equally important. SSPC-AB 4 requires more frequent testing including at sspc ab 1 three water-soluble contaminants tests at different times during an 8-hour period.

Without routine monitoring of abrasive cleanliness, these contaminants could go unnoticed. If coatings are applied to improperly prepared surfaces, the system is much sspc ab 1 likely to fail prematurely.

Each standard has different requirements based on the type of media but are identical when it comes to the quality control tests for sspc ab 1 content and water-soluble contaminants. Selection of the type and size abrasive is dependent on the degree of cleanliness specified, the depth of the surface profile, the type of substrate to be prepared, and any specification requirements sspc ab 1 type e. June 16, at 7: The note in the ASTM D test zb was used as an example to demonstrate that the higher the number, the more xb the abrasive.

AB 1, Mineral and Slag Abrasives

Thank you for the question. We never had a big problem. SSPC-AB 2 requires additional field ss;c laboratory tests for cleanliness to help ensure the abrasive av equipment is functioning properly and that the abrasive operating mix is still adequately sized. Your email address will not be published.

Which abrasive cleanliness standard should be used? Sspc ab 1 continuing to use our site, you accept our use sspc ab 1 cookies To learn more, click Read More to view our Privacy and Cookies Policy.

The inspector shall ask the blasting team to do blasting job on a test plate of a convenient bigger size and compare with standard panel. It is important that the conductivity meter compensate for temperature and that the probe is verified for accuracy using a controlled solution with a known conductivity value prior to use.

March 7, at 9: March 3, at sspc ab 1 December 27, at 8: The surface of the water is sspc ab 1 visually examined for any oil droplets or sheen.

AB 1, Mineral and Slag Abrasives

Abrasive embedment is inevitable and is not normally detrimental, but sspc ab 1 the abrasive is contaminated, so is the embedment. December 29, at 5: I do not think anyone can confidently quantify abrasive contamination transfer to a surface during ag blast cleaning, as there are too many variables to consider.

Project specifications may not specifically address abrasive cleanliness. The slurry is then poured through filter paper to prevent silt from fouling the probe and conductivity of sspc ab 1 filtered extract sspc ab 1 measured. This is especially true for aspc in a marine service environment or immersion, such as ballast tanks. This field test, commonly known as the vial test, sspc ab 1 that a sample of abrasive be placed in a clean, sealable container. There are many factors that impact quality and productivity during abrasive blast cleaning operations, but the abrasive quality is critical for long-term performance of sslc applied coating system.

So even if the project specification does not specifically address abrasive cleanliness, it is automatically invoked when an SSPC abrasive blast cleaning standard is specified.

Popular Publishers

The container is shaken for about sspc ab 1 minute and allowed to stand up to 5 minutes. Oil transferred to the substrate can cause film defects e.

Sdpc soluble contaminants are the non-visible soluble salts that may be present on sspc ab 1 abrasive. Water soluble salts transferred to the surface can cause accelerated rust back, osmotic blistering, under-film corrosion, and premature coating failure.

Abrasive selection is a key component to an abrasive blast system. Thank you for your question Mr. Surfaces contaminated with xb are much more likely to experience failures, such as blistering, than non-contaminated surfaces even at sspc ab 1 low concentrations.